PoE SENSORS

PoE SENSORS

iDRIVE WELL-BUILDING ENVIRONMENTAL SENSOR

The worlds most sophisticated all-in-one, PoE powered, sensor solution enables any intelligent building project to precisely measure a variety of essential environmental parameters including PIR occupancy, ambient light, temperature, CCT colour, humidity, light flicker, VOC gases and ambient noise levels. The ceiling recessed PoE sensor can be powered by standard 802.3at Class 1 PoE network switches enabling easy and rapid installation without the need of certified electricians. Simply, decide the sensor position and connect it using standard Cat6 / 6A structured cabling to build a comprehensive intelligent building sensor network.

iMUNE PARKING SENSOR

Wireless sensors detect and report parking space occupancy directly to iMune®, enabling active parking management features, such as search, navigation and reservation. The easy retrofit solution for parking is installed in minutes. Designed for detecting with the highest reliability if a parking space is occupied or available.

iMUNE SUB DESK OCCUPANCY SENSOR

Saving energy without sacrificing comfort can be effortless with occupancy based controls. The Sub Desk Occupancy Sensor enables a new level of energy saving control for BMS and workspace occupancy solutions. The occupancy sensor uses radio frequency technology to communicate wirelessly with the iMune® control system or iSpayce(TM) workspace monitoring platform to help reduce a buildings carbon footprint by reducing temperatures, switching off lights or electrical loads when a space is unoccupied. Being wireless there is no need to run wiring and installation can be completed in a matter of seconds. The Sub-desk mounted Occupancy Sensor is ideal at detecting when a desk is occupied or vacant based on motion in the space underneath the desk.

iMUNE WATER LEAK DETECTOR

For the detection of accumulations of water at defined horizontal surfaces or positions (e.g. below pipes, fittings and in the area of washing machines in basements or utility rooms; below bath tubs or dishwashers in flats). Suitable for water. WaterSensor eco is equipped with fibre disks that work as a sensor; it does not require an additional power supply. In the case of a leak, the fibre disks expand and generate the required power to send the event message to the iMune® control system. This can be used for example, to shut off the water pipe to prevent further damage from water escaping.

iMUNE MAGNET CONTACT SENSOR – EMCSA (OEM)

EMCS is an energy-harvesting wireless magnet contact sensor for EnOcean systems. Powered by a solar cell, EMCS works absolutely maintenance-free. An integrated energy store allows operation for several days in total darkness. In dark surroundings, a coin cell battery can be retrofitted. The small housing is easy to be mount on windows, on doorframes or on cabinets using the included double-sided adhesive pad or using the also included mounting plate. The ultra-slimmagnet has a preassembled adhesive pad.EMCS supervises an integrated reed contact and reports every status change immediately (open<>closed). In addition, a sign of life signal is send at regular intervals. EMCS provides the option to use Enhanced Security mode with encrypted communication and Rolling Code.

iMUNE PIR & ILLUMINATION SENSOR

The iMune® PIR and Motion Sensor enables a new level of energy saving control for rooms, corridors and other common areas. The sensor reports motion detection and illumination measurements wirelessly using the EnOcean radio standard and therefore does not require any wiring. The sensor is also selfpowered by harvesting energy from indoor light, eliminating the need for periodic battery changes. Key applications include lighting control based on presence and ambient light level as well as occupancy monitoring. The iMune® PIR and Motion Sensor reports regularly the measured light level and the status of the motion detection sensor. The motion sensor is permanently active so that initial motion will be reported immediately.

iMUNE MULTI SENSOR

The iMune® Multi Sensor integrates dedicated sensors for temperature, humidity, illumination, acceleration and magnet contact. Applications are wall-mounted or equipment-mounted sensor solutions for the measurement of temperature, humidity, illumination or acceleration / orientation. The device utilises an integrated solar cell to generate the required energy based on available ambient lighting. Under typical indoor lighting scenarios (200 lux for 6 hours per day) it operates fully self-supplied. For use cases with insufficient available light, it is possible to mount a dedicated backup battery. An integrated NFC interface is implimented, which can be used for device configuration and device commissioning. In addition, it contains an LRN button that can be used for simple commissioning tasks.

iMUNE WIRELESS PIR

Saving energy without sacrificing comfort can be effortless with iMune® occupancy based controls. The iMune® Ceiling Mounted Wireless PIR Sensor enables a new level of energy saving control for rooms, corridors and other common areas. The PIR sensor uses radio frequency technology to communicate wirelessly with the iMune® control system to set back temperatures, turn off lights or electrical loads when a space is unoccupied. Being wireless there is no need to run wiring and installation can be completed in a matter of minutes. The sensor is self-powered by harvesting energy from indoor light, eliminating the need for periodic battery changes.

iMUNE WIRELESS SMOKE ALARM

The iMune® smoke alarm works according to the photoelectric principle. A fire alarm is indicated by a series of repeated sounds, the volume is at least 85dB. Upon activation or test the radio transmitter module sends an alarm message immediately to the iMune® control system. As soon as the alarm terminates, an alarm-end message is sent. Approx. every 30 minutes a status message is sent. This allows monitoring and logging of the sensor status at all times. The power supply of the smoke detector is an internal, non-interchangeable lithium battery with a lifetime averaging 10 years. When the battery is at the end of its life, a short beep sound is produced. The power supply for the radio transmitter module is provided by a solar cell if sufficient brightness is present. If the room brightness is not sufficient for operation, a 3,6V lithium battery 1/2 AA (not included) must be inserted.

iMUNE FEATURES

This iMune® wireless environmental monitoring sensor allows you to monitor live conditions in each room or zone of a building. The temperature and air quality inside a building can impact people’s comfort and wellbeing. Employers have an added responsibility to provide a healthy working environment by maintaining a reasonable temperature and meeting minimum air quality standards.